Please select a category to show the SeaTalk Next Generation cables and components.
Return to the SeaTalkng networking page
In a SeaTalkng installation, a backbone cable runs through the length of the boat.
Individual devices connect to the backbone by spur cables that run to T-pieces on the backbone. The backbone carries both data and power to attached devices. The backbone should be sized so that it will run past every location where an NG or NMEA 2000 device might be installed.
Two backbone cable lengths can be joined together by part A06030, a backbone extender.
![]() |
|
BACKBONE CABLE | |
Available in a number of different cable lengths | |
Part Number | Cable Length |
A06033 | 400mm (15.7") |
A06034 | 1m (3.25') |
A06035 | 3m (9.75') |
A06036 | 5m (16.25') |
A06068 | 9m (29.25') |
A06037 | 20m (65') |
Individual devices connect to the backbone by spur cables that run to T-pieces on the backbone.
![]() |
![]() |
![]() |
|
SPUR CABLES | |||
Cable Type | Spur Cable | Elbow Spur Cable | Spur to Stripped End Cable |
Part Number / Cable Length | A06038 / 0.4m (15.7in) | A06042 / 0.4mm (15.7in) | A06043 / 1m (3.25ft) |
A06039 / 1m (3.25ft) | A06044 / 3m (9.75ft) | ||
A06040 / 3m (9.75ft) | |||
A06041 / 5m (16.25ft) | |||
A06072 / 6m (19.68ft) | |||
Notes | Available in a number of different cable lengths | Available in two different cable lengths. Only contains 5 cores - the Yellow Seatalk1 is not included |
Used for connecting white SeaTalkng Spur Cables to Blue SeaTalkng Backbone Cables
A06028
Used for connecting spurs to the backbone
A06064
Used for extending blue SeaTalkng Backbone Cables
A06030
Go at each end of SeaTalk backbone, two are required per system.
A06031
Place blanking plug in unused SeaTalkng Spur sockets to protect them.
A06032
Terminators go at each end of the Backbone. This is ideal for the RS130. Two Terminators are required per system.
A06074
Used for connecting SeaTalk1 devices to the SeaTalkng network. See what's in the kit.
E22158
Used for connecting an Isolated NMEA 0183 VHF to the SeaTalkng network.
E70196
Used for connecting SeaTalk1 devices to the SeaTalkng network. Converter only - no cables.
R52131
This Starter Kit is perfect to get you going with SeaTalkng. contains: Two Terminators, Power Cable, 5-Way Block, 3m Spur Cable.
T70134
This is a larger backbone kit which contains: Two Terminators, Power Cable, 4 x T-Piece Connectors, 20m Backbone Cable, 2 x 5m Backbone Cable
A25062
SPX Course Computer Spur Cable (900mm), for connection to SeaTalkng. This is supplied with the SPX. (Not applicable to the SPX5)
R12112
This is a 90°, right angle spur connector. Used for the multifunction displays.
A06077
Raymarine cable kit for NMEA gateway
T12217
![]() |
![]() |
![]() |
![]() |
![]() |
|
Enlarge Image | Enlarge Image | Enlarge Image | Enlarge Image | Enlarge Image | |
ADAPTOR CABLES | |||||
Cable Type | DeviceNet Adaptor Cables | ST1 Adaptor Cable (3 Pin) | E-Series to SeaTalkng Adaptor Cable | ST2 Adaptor Cable (5 Pin) | Micro C DeviceNet Adaptor Cables |
Part Number / Cable Length | A06045 / 0.4m (15.7in) DeviceNet Female | A06047 / 0.4m (15.7in) | A06061 / 1.5m (4.92in) | A06048 / 0.4m (15.7in) | A06075 / 0.4m (15.7in) Female |
A06075 / 1.0m (39.4in) DeviceNet Female | A06073 / 1.0m (39.4in) | A06076 / 0.4m (15.7in) Male | |||
A06078 / 0.1m (3.9in) DeviceNet Male | |||||
A06076 / 1.0m (39.4in) DeviceNet Male | |||||
A06046 / 1.5m (59.1in) DeviceNet Male | |||||
Notes | Adapts SeaTalkng to NMEA2000 network. Available with Male or Female ends | An adaptor spur cable to connect a SeaTalk device to a SeaTalkng network. The connection must be made via a 'bridging' device such as an ST70. The 0.4m cable is also available as part of the SeaTalk to SeaTalkng converter kit | An adapter spur cable to connect an E-series Classic display to a SeaTalkng network, using the SeaTalk2 port on the back of the E-Series. | An adaptor spur cable to connect a SeaTalk2 device or network to a SeaTalkng network. | Adapts SeaTalkng to NMEA2000 network. For use with E Series. Available with Male or Female ends |
![]() |
![]() |
|
SEATALKNG POWER CABLES | ||
Part Number | A06049 | A06070 |
Product | Power Cable (Straight) | Power Cable (Right Angle) |
Product Compatibillity | A cable to connect a SeaTalkng backbone to a 12V switched power supply. This provides power to the whole network and attached devices. Only one power cable is used per network. When attached at the mid-point of a network, this cable powers each half of the network independently. |
A right angle cable to connect a SeaTalkng backbone to a 12V switched power supply, or to connect power to an RMK-9. |
Data | Power | Power |
Length | 2m (6.56ft) | 2m (6.56ft) |
In a SeaTalkng installation, a backbone cable runs through the length of the boat.
Individual devices connect to the backbone by spur cables that run to T-pieces on the backbone. The backbone carries both data and power to attached devices. The backbone should be sized so that it will run past every location where an NG or NMEA 2000 device might be installed.
Two backbone cable lengths can be joined together by part A06030, a backbone extender.
![]() |
|
BACKBONE CABLE | |
Available in a number of different cable lengths | |
Part Number | Cable Length |
A06033 | 400mm (15.7") |
A06034 | 1m (3.25') |
A06035 | 3m (9.75') |
A06036 | 5m (16.25') |
A06068 | 9m (29.25') |
A06037 | 20m (65') |
Individual devices connect to the backbone by spur cables that run to T-pieces on the backbone.
![]() |
![]() |
![]() |
|
SPUR CABLES | |||
Cable Type | Spur Cable | Elbow Spur Cable | Spur to Stripped End Cable |
Part Number / Cable Length | A06038 / 0.4m (15.7in) | A06042 / 0.4mm (15.7in) | A06043 / 1m (3.25ft) |
A06039 / 1m (3.25ft) | A06044 / 3m (9.75ft) | ||
A06040 / 3m (9.75ft) | |||
A06041 / 5m (16.25ft) | |||
A06072 / 6m (19.68ft) | |||
Notes | Available in a number of different cable lengths | Available in two different cable lengths. Only contains 5 cores - the Yellow Seatalk1 is not included |
Used for connecting white SeaTalkng Spur Cables to Blue SeaTalkng Backbone Cables
A06028
Used for connecting spurs to the backbone
A06064
Used for extending blue SeaTalkng Backbone Cables
A06030
Go at each end of SeaTalk backbone, two are required per system.
A06031
Place blanking plug in unused SeaTalkng Spur sockets to protect them.
A06032
Terminators go at each end of the Backbone. This is ideal for the RS130. Two Terminators are required per system.
A06074
Used for connecting SeaTalk1 devices to the SeaTalkng network. See what's in the kit.
E22158
Used for connecting an Isolated NMEA 0183 VHF to the SeaTalkng network.
E70196
Used for connecting SeaTalk1 devices to the SeaTalkng network. Converter only - no cables.
R52131
This Starter Kit is perfect to get you going with SeaTalkng. contains: Two Terminators, Power Cable, 5-Way Block, 3m Spur Cable.
T70134
This is a larger backbone kit which contains: Two Terminators, Power Cable, 4 x T-Piece Connectors, 20m Backbone Cable, 2 x 5m Backbone Cable
A25062
SPX Course Computer Spur Cable (900mm), for connection to SeaTalkng. This is supplied with the SPX. (Not applicable to the SPX5)
R12112
This is a 90°, right angle spur connector. Used for the multifunction displays.
A06077
Raymarine cable kit for NMEA gateway
T12217
![]() |
![]() |
![]() |
![]() |
![]() |
|
Enlarge Image | Enlarge Image | Enlarge Image | Enlarge Image | Enlarge Image | |
ADAPTOR CABLES | |||||
Cable Type | DeviceNet Adaptor Cables | ST1 Adaptor Cable (3 Pin) | E-Series to SeaTalkng Adaptor Cable | ST2 Adaptor Cable (5 Pin) | Micro C DeviceNet Adaptor Cables |
Part Number / Cable Length | A06045 / 0.4m (15.7in) DeviceNet Female | A06047 / 0.4m (15.7in) | A06061 / 1.5m (4.92in) | A06048 / 0.4m (15.7in) | A06075 / 0.4m (15.7in) Female |
A06075 / 1.0m (39.4in) DeviceNet Female | A06073 / 1.0m (39.4in) | A06076 / 0.4m (15.7in) Male | |||
A06078 / 0.1m (3.9in) DeviceNet Male | |||||
A06076 / 1.0m (39.4in) DeviceNet Male | |||||
A06046 / 1.5m (59.1in) DeviceNet Male | |||||
Notes | Adapts SeaTalkng to NMEA2000 network. Available with Male or Female ends | An adaptor spur cable to connect a SeaTalk device to a SeaTalkng network. The connection must be made via a 'bridging' device such as an ST70. The 0.4m cable is also available as part of the SeaTalk to SeaTalkng converter kit | An adapter spur cable to connect an E-series Classic display to a SeaTalkng network, using the SeaTalk2 port on the back of the E-Series. | An adaptor spur cable to connect a SeaTalk2 device or network to a SeaTalkng network. | Adapts SeaTalkng to NMEA2000 network. For use with E Series. Available with Male or Female ends |
![]() |
![]() |
|
SEATALKNG POWER CABLES | ||
Part Number | A06049 | A06070 |
Product | Power Cable (Straight) | Power Cable (Right Angle) |
Product Compatibillity | A cable to connect a SeaTalkng backbone to a 12V switched power supply. This provides power to the whole network and attached devices. Only one power cable is used per network. When attached at the mid-point of a network, this cable powers each half of the network independently. |
A right angle cable to connect a SeaTalkng backbone to a 12V switched power supply, or to connect power to an RMK-9. |
Data | Power | Power |
Length | 2m (6.56ft) | 2m (6.56ft) |
2018 © FLIR Systems All rights reserved. Privacy Policy|Copyright Policy|Terms of Use